Solar Panel Steel Structure Calculation & Calculator
Structure Material Take-Off
Estimate aluminium channel, purlin, clamp and bolt quantities for rooftop mounting structures. Adjust any input and the BOQ updates live.
Inputs
Updates liveResults
LiveMaterial take-off for 100 kWp
Flat RCC — Pedestal · 10 tables
Tables
structures
Al Channel
m rails
Structure Wt
kg est.
Material Bill of Quantity
“Aluminium alloy 6061-T6 or 6063-T5 channels used for rooftop mounting. Typical yield: 270 MPa (6063-T5), 310 MPa (6061-T6). IS 733 / IS 3443 govern extrusion specifications.”
About the Structure Material BOQ
The mounting-structure Bill of Quantities (BOQ) estimates the steel or aluminium needed for the module mounting system, driven by the number of modules, the array layout, and the site's wind zone.
Formula
Steel (kg) = Σ (Member length (m) × Unit weight (kg/m)) ≈ Capacity (kWp) × kg/kWp
- Member length
- Total length of each section type — columns, rafters, purlins, bracing
- Unit weight
- Mass per metre of the chosen section (from the steel table for that profile)
- kg/kWp
- Specific steel use — a quick check that varies with wind zone, tilt, height and span
How to calculate it
- 1Fix the array configuration (portrait/landscape, modules per table, tilt).
- 2Determine the design wind load for the site's wind zone (IS 875 Part 3).
- 3Size the purlins, rafters, columns and bracing to carry dead + wind load within allowable stress (IS 800).
- 4Total the member lengths and convert to weight — a hot-dip galvanised steel rooftop structure is typically ~40–60 kg per kWp.
Worked example
A 100 kWp rooftop array at roughly 50 kg/kWp needs about 5 tonnes of galvanised steel, plus fasteners and base plates — refined by the exact wind zone and roof type.
What you can calculate
- Channel / purlin kg
- Clamp count
- Nut bolt count
- Wastage factor
Standards & references
Frequently asked questions
How do you calculate a steel structure for a solar farm?
First fix the table layout (modules per table, tilt, ground clearance) and design the members for the site wind speed per IS 875 (Part 3). Then list every member — columns, rafters, purlins, bracing — multiply each length by the section's unit weight (kg/m) and add 3–5% for base plates, cleats and fasteners. Divide the total by the plant kWp to sanity-check the kg/kWp against similar projects in the same wind zone.
Does a solar carport or shade structure need more steel than a ground mount?
Yes — considerably more per kWp. Elevated structures (carports, shade structures, high-clearance agri-PV) need taller, heavier columns, longer spans and stronger foundations to carry wind and live loads, so they should always be designed and checked by a structural engineer rather than estimated from a ground-mount ratio.
How much steel does a solar mounting structure need?
A galvanised-steel rooftop mounting structure typically uses about 40–60 kg of steel per kWp; ground-mount structures are heavier. The exact figure depends on the wind zone, span, tilt, and whether steel or aluminium is used.
Ready to build your solar project?
Get free quotes from verified EPCs and installers across India.
You might also need
Pedestal Height
Calculate front and rear pedestal heights for target module tilt on flat rooftops
OpenModule Layout Planner
Plan tables, rows and string configuration for a rooftop array
OpenSetback from Parapet
Calculate minimum module setback from parapet walls to avoid shading
OpenBallast Weight
Calculate ballast required to resist IS 875 Part 3 wind uplift without penetrations
OpenWind Load (Rooftop)
Calculate uplift and lateral wind forces on rooftop PV modules per IS 875 Part 3
OpenAnchor Bolt Sizing
Determine anchor bolt count, diameter, and embedment depth for structural loads
Open